因板式換熱機組的流道截面積較窄,板式換熱機組中的換熱器內的沉淀物和懸浮物聚集在角孔處和導流區內，導致該處的流道面積大為減小，造成壓降過大，對于板式換熱機組的壓降過大，如何巧妙的解決呢？下面由山東新壬的技術小編給大家詳細總結一下:

　　1、清除換熱器流道中的臟物或板片結垢，對于新運行的系統，根據實際情況每周清洗一次。清洗板片表面水垢（主要指CaCO3）時，選用含0.3氨基磺酸溶液或含0.3烏洛托平、0.2苯胺、0.1硫氰酸鉀的0.8硝酸溶液作為清洗液，清洗溫度4O～6O℃。不拆卸設備化學浸泡清洗時，要打開換熱器冷介質進、出口，或安裝設備時在介質進、出口接管上安裝DN25清洗口，將配好的清洗液注入設備中，浸泡后用清水清洗干凈殘留酸液，使pH≥7。拆開清洗時，將板片在清洗液中浸泡30min，然后用軟刷輕刷結垢，最后用清水清洗干凈。清洗過程中應避免損傷板片與橡膠墊。若采用不拆卸機械反沖洗方法，應事先在介質進、出口管路上接一管口，將設備與機械清洗車連接，把清洗液按介質流動的反方向注入設備，循環清洗時間10～15min，介質流速控制在0.05～0.15m/s。最后再用清水循環幾遍，使清水中Cl質量濃度控制在25mg/I以下。
　　2、二次循環水最好采用經過軟化處理后的軟水，一般要求水中懸浮物質量濃度不大于5mg/L、雜質直徑不大于3 mm、pH≥7。當水溫不大于95℃時，Ca 、Mg濃度應不大于2 mmol/L；當水溫大于95℃時，Ca 、Mg 濃度應不大于0．3mmol/L、溶解氧質量濃度應不大于0．1 mg/L。
　　3、對于集中供熱系統，可以采用一次向二次補水的方法。
　　以上是板式換熱機組中的幾種常見故障,要對于這種故障要及時的解決處理,經常性做好維護工作~~